Cnc Axis Digitizing

6Axis CNC Digital Controller 7.8A, 80V & 4.2A, 50V Mill kit


6Axis CNC Digital Controller 7.8A, 80V & 4.2A, 50V Mill kit
6Axis CNC Digital Controller 7.8A, 80V & 4.2A, 50V Mill kit
6Axis CNC Digital Controller 7.8A, 80V & 4.2A, 50V Mill kit

6Axis CNC Digital Controller 7.8A, 80V & 4.2A, 50V Mill kit    6Axis CNC Digital Controller 7.8A, 80V & 4.2A, 50V Mill kit

3 PCS CNC Stepper Driver DQ860MA with 7.8A peak current, 256 Microstep, 24-80VDC. 3 PCS CNC Stepper Driver DQ542MA with 4.2A peak current, 128Microstep, 50VDC. 2 PCS Breakout Board + 2PCS Cable.

High Quality CNC Stepper Driver DQ860MA + Stepper Driver DQ542MA + Breakout Board + Cable. DQ860MA is a type of two-phase hybrid stepping motor driver, The drive voltage of which is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 86mm outside diameter and less than 7.8A phase current. This circuit that it adopts is smiliar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DQ860MA run under high speed is also significantly higher than the other two-phase driver, whats more, the positioning accuracy is also higher.

It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on. Average current control, 2-phase sinusoidal output current drive. Supply voltage from 24VDC to 80VDC. Overvoltage, under voltage, overcorrect, phase short circuit protection. 15 channels subdivision and automatic idle-current reduction.

8 channels output phase current setting. Motor torque is related with speed, but not related with step/revolution. High hording torque under high speed. Low cost and good high-speed.

Supply voltage up to +80VD. Suitable for-2-phase and 4-phase motors.

Rated Output current up to. Peak current for 7.8. Dip switch current setting 8different. Pulse frequency up to 200KHz. Small size (14310737), Weight:0.5. 2, Stepper Motor Driver DQ542MA.

If you want to find more information for our driver, please check the link at below. DQ542MA is a type of two-phase hybrid stepping motor driver, The drive voltage of which is from 18VDC to 50VDC.

It is designed for use with 2-phase hybrid stepper motor of all kinds with. Outside diameter and less than. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration.

Hording torque when DQ542MA run under high speed is also significantly higher than the other two-phase driver, whats more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, Computer embroider machine, packing machines and so on. Supply voltage from 18VDC to 50VDC. Not condensation, no water droplets. Prohibition of combustible gases and conductive dust.

Built in DB25 male connector. DB25 Output Pin:P1, P2, P3, P4, P5, P6, P7, P8, P9, P14, P16, P17. DB25 Input Pin: P10, P11, P12, P13, P15. High quality with Surface-mount Tech. More Order quantites, more discount!!

Our products are mainly used in robotization, Spinning Automatization, Printing, Packing, Medica Machine, Make-up Equipment, Communication, Household Appliance, Water Pump, Milling Machine, Engraver Machine, CNC Routers.. Etc automatic equipment of various trades.

The item "6Axis CNC Digital Controller 7.8A, 80V & 4.2A, 50V Mill kit" is in sale since Wednesday, August 21, 2019. This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives". The seller is "wantaimotor99" and is located in Madrid.

This item can be shipped worldwide.
  1. Model: DQ860MA + DQ542MA Driver
  2. MPN: Does Not Apply
  3. Brand: Wantai Motor
  4. Country of Manufacture: China

6Axis CNC Digital Controller 7.8A, 80V & 4.2A, 50V Mill kit    6Axis CNC Digital Controller 7.8A, 80V & 4.2A, 50V Mill kit